PDA

View Full Version : Taking out a video card!


Monkeee
12-31-2004, 03:25 AM
well i'm upgrading my video card... and well i suck at hardware so just wondering, is taking out the video card diffacult!? is it just like taking out ram?
tesco
12-31-2004, 03:36 AM
it's as easy as ram. :lol:

it's simply unplugging the power wire (same one as a hard drive's power wire) if you have a card that needs one (just the newer ones), then taking out 1 single screw, and pulling teh card out (carefully).
Monkeee
12-31-2004, 03:39 AM
i c.. do all of the cards have power cords thingy? do the Radeon 9800 PRO have one? do u just take it out? o GAWD WHAT IF IT SNAPS WHEN I TAKE IT OUT!!! DEAR GOD!!
SciManAl
12-31-2004, 03:39 AM
clear
tesco
12-31-2004, 04:04 AM
i c.. do all of the cards have power cords thingy? do the Radeon 9800 PRO have one? do u just take it out? o GAWD WHAT IF IT SNAPS WHEN I TAKE IT OUT!!! DEAR GOD!!
it won't snap unless you like hammer it or something. :huh:

seriously the only way you could go wrong is by pulling on the fan\heatsink or a capacitor or something.
just pull it on edges where there's no little circuit bits and you'll be fine. :)
SaYiaN
12-31-2004, 07:59 AM
you could always ask one of ur 'expert' comp friends to put it in for you or take it out..
Monkeee
12-31-2004, 08:17 AM
why? like they said it would just take 30-60 seconds.... it would be kind of pointless
razorsharp013
12-31-2004, 08:33 AM
Well there is that whole exploding GPU problem some cards have, but I'm sure you'll be ok. :P
cpt_azad
12-31-2004, 10:41 AM
ya do what the ppl above said, but remember one important thing dude, DO NOT UNDER ANY CIRCUMSTANCE TOUCH THE GOLDEN PART (PINS) AT THE BOTTOM OF THE CARD, THE GOLDEN PART THAT GOES INTO THE AGP/PCI SLOT.

u have been warned.
colt45joe
12-31-2004, 11:07 AM
some AGP slots have a little thingy that snaps into the card so it stays in place...so if your pulling and it doesnt come out..you might have that thingy, so youd have to press it in, then the card can come out safely.
cpt_azad
12-31-2004, 11:56 AM
as long as the gold part is left untouched, everyone is happy :)
Duffman
12-31-2004, 12:41 PM
try not to touch anything metal, those caps hold a whole lotta electricity, a friends cousin died doing it once.
Virtualbody1234
12-31-2004, 01:48 PM
Boom!!!
clocker
12-31-2004, 02:01 PM
some AGP slots have a little thingy that snaps into the card so it stays in place...so if your pulling and it doesnt come out..you might have that thingy, so youd have to press it in, then the card can come out safely.
That "little thingie" is a retainer clip very much like the ones on your DIMM (RAM) slots.
Some boards (DFI, for instance) use a retainer that springs from the side ( a terrible arrangement, IMO), but they all do the same thing....retain the vid card on the far end of the AGP port.
Pay attention and you'll be fine.
tesco
12-31-2004, 03:45 PM
ya do what the ppl above said, but remember one important thing dude, DO NOT UNDER ANY CIRCUMSTANCE TOUCH THE GOLDEN PART (PINS) AT THE BOTTOM OF THE CARD, THE GOLDEN PART THAT GOES INTO THE AGP/PCI SLOT.

u have been warned.
:huh:
static?
colt45joe
12-31-2004, 09:57 PM
That "little thingie" is a retainer clip very much like the ones on your DIMM (RAM) slots.
Some boards (DFI, for instance) use a retainer that springs from the side ( a terrible arrangement, IMO), but they all do the same thing....retain the vid card on the far end of the AGP port.
Pay attention and you'll be fine.

exactly
Monkeee
12-31-2004, 10:02 PM
well i do have a screwless case so i think i have one of thoes clips....

i think i'm going to die....
SciManAl
12-31-2004, 11:45 PM
clear
3RA1N1AC
01-02-2005, 11:30 AM
try not to touch anything metal, those caps hold a whole lotta electricity, a friends cousin died doing it once.
he had his pants off while touching this metal, didn't he. >:|
cpt_azad
01-02-2005, 11:39 AM
lol, no brainy no that's just wrong.


remember, dont touch the gold pins.
fkdup74
01-02-2005, 02:40 PM
This isnt nearly as hard as this is sounding,
just be slow with it, if its your first try
just think of a how it goes in and out,
dont apply too much preasure, but thats not too bad a problem,
try to touch it not so much, it makes it dirty

ummmmm..........:blink:
SciManAl
01-02-2005, 03:19 PM
clear
fkdup74
01-02-2005, 03:27 PM
you guys are screaming dont do this dont do that, jeez,
hehe look at you sig fkdup

hehe, you like that huh? :P
of course its there as a joke, saw some dude post that in another forum
actually, after RMAs on a vid card, RAM, and a floppy....
i use teh anti-static wristband now...
and i actually power off teh PC now too :lol: