Quick Help On Ram / Motherboard

Printable View

04-15-2003, 08:42 PM
ooo

Quote:

SimpleTech (Simple Technologies) 512MB DDR PC2700 Major Brand Chip - OEM
Retail. 184-pin. Non-parity, Gold Contacts, 6 Layer PCB, CL=2.5, 2.5Volt, PC2700=DDR333, Lifetime Warranty. Part# RB2700DDR/512

Quote:

ASUS P4PE/L Motherboard for Intel P4 478 Retail w/ Intel Hyper-Threading Technology, Onboard LAN, SoundMAX Digital Audio System
***1st Intel chips that TRUELY support DDR333 PC2700***
Specifications:
Supported CPU: Socket 478 for Intel® Pentium® 4/ Celeron up to 3GHz
Chipset: Intel 845PE
FSB: 533 / 400 MHz
RAM: 3 x184-pin DDR333 PC2700/PC2100/PC1600Max 2GB
IDE: 2 x UltraDMA 100/66/33
Slots: 1 x AGP 4X 6 x PC
Ports: 1x LPT, 2x COM, 2x PS/2, 1x RJ45,4xUSB2.0 Audio Ports
Onboard Audio: ADI1980 6-channel CODEC
Onboard LAN:BroadCom 10/100 Mbps Ethernet controller Model#: P4PE/L 

These two should fit right?

since the ram doesnt click in ...... right now...
04-15-2003, 08:48 PM
amphoteric88

these seem compatible. make sure you're trying to insert the ram the right way round
remember it can also be hard to insert the ram first time round, just be patient and don't force it
04-15-2003, 08:50 PM
ooo

ummm well i think it's in... you know what i will take a picture of how it is in so far.... secondly... my hand is brusing up... can you explain to me how to take off the face plate of the case... i mean the back part where the

onboard USB port, sound port, mouse and keyboard thing is placed... i can get it off...
04-15-2003, 08:58 PM
ooo

Click here to see the problem im having...
04-15-2003, 09:01 PM
ooo

umm got hte back plate off but my ram still wont fit...

i broke the face plate off w/ a screw driver... kept pounding it w/ it...

RAM STILL WONT FIT!!
04-15-2003, 09:19 PM
amphoteric88

make sure you're putting the ram in the right way round first. the pins are split into two uneven sections, one is 110 pins and the other is 74 i think. make sure the little plastic bridge in the dimm slot is in the right bit. you need to push it in till the plastic retaining pins click in. good luck and be patient
04-15-2003, 09:26 PM
Lamsey

- open the little white levers at either side (ie push them away from the socket)
- Place the RAM into the socket, matching up the long and short bits of the stick with the long and short bits in the socket
- Push down on the RAM at one side until the white lever snaps into place
- push down on the other side until the lever clicks into place

Never use excessive force, you'll either damage the equipment or yourself.

To release RAM later, just open the little levers at either side and the stick will pop out.

Hope this helps :)
04-15-2003, 09:31 PM
ooo

eh well i did all that it just doesnt go into the whole... lolz.... as u can see if u looked at the pics.. arg i cant type good... i scratched one of my fingers on the metal....

http://us.f1.yahoofs.com/users/7e79f460/bc...cW6Hn.AowXdxaAt

look at that pic

u can see that the RAM closing thing is hitting the green part of the RAM
04-15-2003, 09:36 PM
Lamsey

You'll just have to press carefully until it slips in... :(

Make sure you press one side down then the other...
04-16-2003, 12:10 AM
ooo

eh... i got it figured out! finally.... lolz got 2 cuts... bleeding badly... hardware done

NOW I NEED HELP ON SOFTWARE

i got 2 cd rom drives and a hardware... im trying to install windows but it saids something about dos missing and stuff...

so what do i do now?

i can acess

a:
x:
y:

x = cdrw
y = cdrom

a = i have no clue...
04-16-2003, 02:54 AM
Somebody1234

@Soul814,

Quote:

eh... i got it figured out! finally

Once you figure out something it would be considerate of you to tell us what worked. There are other people who read this and you could be of some help to them too.
04-16-2003, 08:12 PM
ooo

Ooo.... well i just pushed it in like lamsey said.... i popped one side in after 30minutes of trial it finnaly went in lolz
04-17-2003, 07:19 PM
Schmiggy_JK23

ya. when i first got my ram stick, and my abit kr7a, the ram was a bitch to get in also. Just took some time, and steady, but heavy pressure on each side. Not like the old edo days, tahts for sure.

Are u using a bootable windows cd? Then just set ur cdrom drive as the first boot device in your bios, then boot and install from the cd.
04-17-2003, 08:49 PM
ooo

eh thanks everyone i got my new computer running... :P

well i made 6 boot up floppies for xp pro corp....

then i ran the set up used the new xp pro disk i made to install the first portion of the setup

then i used my old win xp pro disk to install during the second portion

since there was some errors in each disk...