Unplug USB - Computer Shut Off

I just built my new computer. I installed my printer drivers and hooked it up. When I unplugged the USB cable that hooks the printer to my computer, my computer immediately shut off. The printer was still on.

The computer doesn't shut off when I unplug the USB cord and the pritner is off. This doesn't seem normal that my ocmputer should shut off just b/c the printer is on. I did this with my other computer and it didn't shut off.

Any ideas why this is happening?



Also, I installed a firewire PCI card onto my motherboard. When I finished, my computer wouldnt turn on. I turned off my power surge protector (this is what my computer is plugged into) and turned it back on thent he ocmputer would turn on. But when it came on it said CMOS Checksum Bad - F1 to run setup, F2 to restore default values.

I tried F1 and everyhting in the BIOS and CMOS looked normal (althoguh I don't kwno much abotu BIOS or CMOS). I hit ESC and Windows started. The next tiem I restarte dmy PC, the same CMOS error came up, but this time I hit F2. Things seem to be ok now, but I'm wodnering, what caused CMOS Checksum Bad?

Thanks

Did you stop or uninstall the printer before unpluging?

If not then it's incompatibility of the PC's and your USB printer is the only reason I can think off. I don't think it's a hassle to switch off your printer 1st before unplug it.

BTW why do you want to unplug & plug your USB printer? USB is a plug & play device but the physical port itself is not a true plug & play device. You will wear & tear your USB faster is do a lot of plug & unplug.

For the "CMOS Checksum Bad - F1 to run setup, F2 to restore default values." just press F2 it's will solve it. If it's happen again the change the CMOS battery.

I don't need to unplug and plug in my printer while it is on, I just thought the fact that doing so shut off my computer could be the manifestation of some sort of hidden problem within the computer. In other words, it's not that I will be unplugging often, it's just that I was wondering if something was wrong, b/c I don't think I have this issue with other computers.

Thanks for the info about CMOS. Do you know what could have caused it, though? Or what caused my computer to not turn on?

Thanks

Quote:

---

Originally Posted by ninjamonkey

I just built my new computer.

---

Quote:

---

Originally Posted by ulun64

...change the CMOS battery.

---

Unlikely that the battery (which is new) is at fault.

Quote:

---

Originally Posted by ninjamonkey

I don't need to unplug and plug in my printer while it is on, I just thought the fact that doing so shut off my computer could be the manifestation of some sort of hidden problem within the computer. In other words, it's not that I will be unplugging often, it's just that I was wondering if something was wrong, b/c I don't think I have this issue with other computers.

Thanks for the info about CMOS. Do you know what could have caused it, though? Or what caused my computer to not turn on?

Thanks

---

I think you have to reset the CMOS with the pins on the mobo whenever you get a new one (recommended).

Did you disconnect the computer from the mains before installing the Firewire PCI card. From the way you've described things I'm guessing you didn't.

Many people don't realise that power is always supplied to the motherboard even though the system seems to be off, unless you disconnect the mains supply or use the switch on the back of the PSU.

The result is that inserting or removing a PCI card or memory stick will often send a small spike across the motherboard. If this happens you can expect to see cmos corruption at the very least. At worst, you could blow the motherboard or the PCI card.

I'm not sure about the USB port problem, does it happen every time or was it just a one-off? And is this after the situation with the Firewire card? If so, it may be an indicator of motherboard damage.

If the port is connected to the motherboard by a cable, check the wiring.
If it is connected directly to the board, check that the board doesn't short to the case when you remove the printer cable, and that the bits of the case that are supposed to be grounded (like round the ports) are making good connection.

When you unplug the USB device does the compute rlitterally shut off or do you mean it seems to restart.
If it restarts then then you're likely getting a BSOD because of unplugging the device.

Quote:

---

Originally Posted by rossco

When you unplug the USB device does the compute rlitterally shut off or do you mean it seems to restart.
If it restarts then then you're likely getting a BSOD because of unplugging the device.

---

Good point. Disabling the Automatically restart "feature" would show the error msg instead of restarting.

The computer went black and restarted

Also, in regards to the firewire card, no I didnt disconnect the mains. Thanks for the info. Hopefully I didnt do any damage.

Quote:

---

Originally Posted by rossco

....If it restarts then then you're likely getting a BSOD because of unplugging the device.

---

+1

Hmm, what's BSOD?

Blue Screen Of Death.

As previously stated, you would get a BSOD with an error code if you disable the Automatically restart feature that is built-in Windows XP. That error code can help pinpoint a solution to your problem.

It can be found in: System Properties>Advanced tab>Startup and Recovery settings>System Failure section.

Quote:

---

Originally Posted by ninjamonkey

The computer went black and restarted

---

In that cause right click my computer ->> properties ->> advanced ->> startup and recovery settings ->> uncheck automatically restart
Then next time you will get a BSOD. Write down the error then google it.
Likely this is a driver problem.;)