my dvd drive is a 20x but never burns higher than 7x or so. if i burn at 16x i get bad burns so i am stuck at 8x.
i have tried tons of different media and always get the same results. i am currently using verbatim 16x dvd+r
Printable View
my dvd drive is a 20x but never burns higher than 7x or so. if i burn at 16x i get bad burns so i am stuck at 8x.
i have tried tons of different media and always get the same results. i am currently using verbatim 16x dvd+r
You can burn Data at very high speeds but not Video or Images, it's just the way it works.;)Quote:
Originally Posted by kooftspc11
do you mean raw video or encoded video? would burning an xvid be considered video or data?Quote:
Originally Posted by dodgy368You can burn Data at very high speeds but not Video or Images, it's just the way it works.;)Quote:
Originally Posted by kooftspc11
Any kind of video needs to be burned slower than say text documents.Quote:
Originally Posted by kooftspc11do you mean raw video or encoded video? would burning an xvid be considered video or data?Quote:
Originally Posted by dodgy368
it's also limited by the speed of the media you are using. that's why you're not burning at 20x. What kind of burner do you have? Maybe a firmware upgrade would help.
Who says?:blink:Quote:
Originally Posted by dodgy368Any kind of video needs to be burned slower than say text documents.Quote:
Originally Posted by kooftspc11
probably because cd's burn at 48x usually, dvd's burn alot slower (8x?). and if you are trying to burn an avi to dvd it can go alot slower b/c it has to convert. but if you are just burning, everything should go the same speed.
if you're using an IDE drive:
make sure you have the drive plugged into a channel that doesn't have an IDE hard drive on it.
make sure you have DMA enabled on the channel that the drive is plugged into.
make sure you're using an 80 conductor IDE cable.
make sure you have the master/slave/cable select jumper on the drive set properly.
One thing you need to realise, the write speed is not constant across the full width of the disk. You only get full speed near the outer edges of the disk, otherwise the disk would have to spin too fast. Your drive should take care of that automatically though.
That said, you shouldn't see any loss in quality when it finally gets up to the highest speed. In addition, all the recording on DVDs is pure digital data, the quality of the playback should not be affected by the recording speed, you can either read the data or you can't. In other words, the playback doesn't degrade, it just stops, although this is overcome in software.
Audio CDs are different, the data is encoded in such a way that recording speed can affect playback. In theory the chances of data recovery are higher, but only on players which read the full digital data. Most players aren't capable of doing that sort of recovery which is where the quality of playback is degraded on a poor recording.
The bottom line is that if you can't read disks written at the highest speeds, then either the media or the writer is faulty. Since you've tried different media types, and assuming that you aren't doing something silly like putting your fingerprints on the unrecorded disk, I'd suggest you've got a faulty writer.
You need to use good quality media and set the drive as master
That doesn't sound correct at all. =/Quote:
Originally Posted by dodgy368Any kind of video needs to be burned slower than say text documents.Quote:
Originally Posted by kooftspc11
I have an 18x DVD writer, and I use 16x DVD-R's. I burn all my movies at 16x.
I stand corrected.:)Quote:
Originally Posted by Rip The JackerThat doesn't sound correct at all. =/Quote:
Originally Posted by dodgy368
I have an 18x DVD writer, and I use 16x DVD-R's. I burn all my movies at 16x.
I based my statement on the experience of myself and friends that all have to burn video at slower speeds so that we don't end up with a load of coasters.
its better 2 write at 8x for dvds becoz it will last longer. and some drives dont read it if u write at 18 r 20x