Printable View
When i power on my PC everything powers up but the PC does not boot until i pres the reset button
when i remove the power connector from my 120GB primary HD (a few month old) everything boots up ok first time
i have a Gigabyte GA7 VR mobo
AMD 2100+ Athlon XP
MSI Geforce FX 5600 256MB
512 MB Ram
2 HD
1 DVD
1 CDRW
300W PSU
check BIOS and make sure that the bios are set to boot from the hard drive with your operating system before the one having problems. i would put the boot order into this order.
floppy drive first (if any)
then cd-rom drive second
and your hard drive with the Operating system is last.
incase your bios sets up by selecting ide0, ide 1, ide 2, ide 3. IDE 0 will be your master primary drive (most liekly one with OS on it), slave primary will be ide1, master secondary wil be ide2, slave secondary will be ide3. you will have to check where each of your drive are hooked up on your IDE cables tro know which is primary secondary master's and slave's, etc.
i dont even get to the bios or post, the screen just stays in standby mode and i dont get any bios beeps
oh i c, your power supply might not be a high enough wattage. try unplugging a cd-rom drive or floppy drive and then turn it on and see if it posts.Quote:
Originally posted by ObiWan@17 March 2004 - 15:09
i dont even get to the bios or post, the screen just stays in standby mode and i dont get any bios beeps
oh i c, your power supply might not be a high enough wattage. try unplugging a cd-rom drive or floppy drive and then turn it on and see if it posts. [/b][/quote]Quote:
Originally posted by ROSSCO_2004+17 March 2004 - 14:17--></div><table border='0' align='center' width='95%' cellpadding='3' cellspacing='1'><tr><td>QUOTE (ROSSCO_2004 @ 17 March 2004 - 14:17)</td></tr><tr><td id='QUOTE'> <!--QuoteBegin-ObiWan@17 March 2004 - 15:09
i dont even get to the bios or post, the screen just stays in standby mode and i dont get any bios beeps
This happened to me before, changing out the power supply fixed it.
i think i'll try changing the PSU
just try unplugging the cd-rom drives and see if it works like that, if so get a higher wattage PSU. BUT TEST IT BEFORE YOU GO OFF TO BUY SO YOU DONT WASTE UR MONEY!Quote:
Originally posted by ObiWan@17 March 2004 - 15:41
i think i'll try changing the PSU
will do, besides i will just borrow a PSU to test it before buying one
ok, im just looking out for ya, didnt want you to buy a psu and then find out that wasnt the problem :) (but i think it is)Quote:
Originally posted by ObiWan@17 March 2004 - 15:57
will do, besides i will just borrow a PSU to test it before buying one
There's normally an option for hard drive boot delay in the BIOS.
I don't think it's your problem, but it wouldn't hurt to set this to 1 or 2 seconds just to see if it's because the drive's a bit slow starting up - mind you, if it is slow starting, I'd say there was a problem with it.
Try a new set of IDE cables.I had one go bad on me before and I couldn't get anywhere with more than one thing plugged into each IDE.If I unplugged my second harddrive and my spare cdrom everything went fine.
I changed the PSU and it was causing the problem (as expected)
thanks for the help
no problem! :DQuote:
Originally posted by ObiWan@18 March 2004 - 14:17
I changed the PSU and it was causing the problem (as expected)
thanks for the help
Good job dude!
Whats a PSU :huh: ?
:lol: Power Supply Unit. :lol:Quote:
Originally posted by GrubMe@18 March 2004 - 14:39
Good job dude!
Whats a PSU :huh: ?
Hahah thanks!
I can build a comp but don't really know about those computer words well only some.