-
Old Guy
You don't even need to use Virtualdub. TMPGenc can convert the entire file from .avi to .mpg as is (you might need to change some priorities in the environment settings). But I don't recommend overburning either.
-
-
02-12-2003, 03:05 AM
Movies & TV -
#12
T H F C f a n
BT Rep: +1
You don't even need to use Virtualdub. TMPGenc can convert the entire file from .avi to .mpg
That is very true and can bring good results. I do find though that sometimes this causes audio synch problems. This is prevented by saving the audio first with virtualdub, plus it only takes 5 mins to do.
-
-
02-12-2003, 03:59 AM
Movies & TV -
#13
Poster
step by step brother
click here
vcd help has quirky navigation
but youll find alot of answers
-
-
02-12-2003, 09:20 AM
Movies & TV -
#14
Poster
Why when I use TMPGenc the file originally is about 680,000 kb, but after converting it to mpeg it becomes over 2,000,000 kb ??? Am I doing something wrong ??? I read the vcdhelp.com and the dvdrhelp.com links but my file becomes WAY too big. Is there a way to shrink it to close to normal while still retaining most of it's visual quality. I have Nero 5.5.1.8 -something like that- and I have the newest version of TMPGenc off the website as well as virtual dub and the mp3 Freeze Virtual Dub... if any of this helps.
-
-
02-12-2003, 10:44 AM
Movies & TV -
#15
Poster
if the file is around 700 mbs or less, it should convert to around the same size, if your following step by step, im really not sure as to what your problem is, it sounds like your saving it as an uncompressed format....my best advice is to split the file up with tmpgenc or virtual dub and then encode, ive had so much of the same issues b4, and the results will vary from file to file...
if all else fails, cut the file up with Vdub m8
the worst that could happen is youll end up with a 4 disk high quality movie ....
-
-
02-12-2003, 02:49 PM
Movies & TV -
#16
Poster
use VDub to extract the audio to a wave file. it saves probs ocuring right at the end.
still in VDub, click >file>file information. REmember the frame rate number (either 23.96 or 24, 25, 29.96 fps..its in the top box)
in TMPEGENC load the wizard. select (NTSC if the file was 29.976 fps; NTSC film if it was 23.976 or 24 fps; PAL if it was 25fps) then >next
select the video and audio files you have. >next >next
on wizard page 4/5, select CD-R 74min or CD-R 80min (depending on which size CD you use)
click Expert>system
right click on stream type, and click unlock..ignore the error msg (click yes).
the box on the right should now be usable..click on MPEG1 - Video CD-non standard
go to video tab. Right Click "frame rate">unlock (again ignore error msg)
go to audio tab. Right Click "frame rate">unlock (again ignore error msg)
go to advanced tab> video arrange method drop down box. Change this to full screen kep aspect ratio
click OK, and return to project wizard 4/5
now on this screen, it'll tel you how many % of one disk its gona fill. If this number is like 199% then its probably best to just do it how it is.
If this is anything less, then you can play with it. (Ive done films up to around 170% and they've been absolutely fine)
basically the 2 unlocked frame rates are the quality. You can reduce these till the film is 99% of the disk. If you have a lot to reduce by, then it is perfectly fine to reduce the audio bitrate to 160. this is still acceptable quality. I also usually reduce the video bitrate to around 900. This again is fine, though in the future you may want to play with these numbers.
Click >next, specify a filename and click OK.
There you go, I think I included everything
Oh yeah, if you want to up the quality but double the encode time, in Project Wizard 4/5>Expert>video>rate control mode>change to 2 pass VBR, though im not convinced myself
EDIT: clarity
-
-
02-13-2003, 12:17 AM
Movies & TV -
#17
Poster
I'll try this vivitron 15 and see if it works. I'll leave the encoding while I go to work since I'm sure it'll take a while .....
-
-
02-13-2003, 02:18 AM
Movies & TV -
#18
Poster
-
-
02-13-2003, 07:01 AM
Movies & TV -
#19
Poster
I got an "illegal floating decimal" error at 12 % .... what happened ???? Also I checked my fps. with VDub and it's none of the above ... it's 29.971, what do I do about that ???
-
-
02-13-2003, 08:10 AM
Movies & TV -
#20
Poster
look at the link accat13 gave, to check you have the right codec installed. This might be the problem for the illegal floating point error. Or download the klite codec pack. (available from here i think.
If your bitrate is 29.971 then use 29.976. Im not sure how accurate it should be, but I never have any problems with using stg similar, i just always use the nearest value (i.e. 24fps works ok on 23.976fps setting, so i usually leave it.) (NB, in the future, if you want to change it, right click on frame rate in expert, and click unlock. this gives you a drop down menu of settings)
anyway, it sounds to me to be a codec problem, try that, if not let me know.
PS, if you PM me the sig2dat link, ill download it, and try it for you
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks