Cleaning Screen
the process we've used for many years which has not scratched or smeared a single screen.
2 soft clean cotton cloth pieces about one foot square each (Chux superwipes are ideal). Dampen with clean water and squeeze out excess water. If the TFT screen has many greasy fingerprints and marks, a TINY amount of gentle detergent (not solvent or ammonia based) on one of these. Gentle clean with this cloth first, don't allow the liquid to dry on the screen, then the damp cloth. Finally polish and dry with a soft clean hand towel. Don't use excess pressure on any part of the screen.
I'd definitely keep away from Windex, CRT and glass/lens cleaning solutions.
Fan Vents
Take you r vacuum cleaner or compressed air
and burst /sck the dirt out of the vents
this will improove ventilation
kill overheating and worst of all noise- seriuoslyKeyboard -Sticky KeysROSSCO_2004
when you are vacuming teh fans i would put a pencil in to stop it spinning or else the bearings get worn out andthe fan starts getting loud and rattely.
The cause of most laptopdisfunction is spilled coffee / drinks etc on keyboard
do the bellow
* Cleaning materials:
* Cotton swabs
* Cosmetic foam rubber cleaning pads ( use only with naptha (lighter fluid), NOT alcohol)
* Paper towels
* Rubbing alcohol
* Water
* Lighter fluid (naptha)
* Fine tipped tweezers
* Scissors
* Kitchen strainer
* Household cleaner, Windex or equivalent
* Super Lube Dry Film spray (critical - DO NOT SU
BSTUTUTE ! K-Mart automotive.
* This is a PTFE (teflon) based lubricant which dries perfectly DRY and is ideally suited for this application.
Proceed as follows:
DISASSEMBLE
IMPORTANT: Make a keyboard map so you know where each key goes.
Carefully pry each key loose with a small screwdriver and place in a container. They pop off. DO NOT use excessive force. There may be a small rubber piece for each key. Remove all of these and place in a separate container. CAREFUL, these are small and like to jump away.
CLEAN KEYBOARD ( do this well...... you will be wonderfully rewarded )
Clean the keyboard with cotton swabs SLIGHTLY DAMPENED with water. Replace these often and BE SURE they are only slightly damp. If they are too wet the excess water will contaminate the keyboard through capillary action. This will clean all water soluble contaminants like Coca-Cola, coffee, and sugar residue. For the very small places, cut the foam rubber into small pieces and use the tweezers, again SLIGHTLY DAMPENED, for cleaning. You must clean each and every key space, inside and out, this is critical since this is where the key touches and moves.
Repeat this procedure again using rubbing alcohol and cotton swabs but NOT the foam rubber as it disintegrates when used with alcohol.
Finally repeat this procedure using naptha (lighter fluid) and foam rubber. You can clean even the smallest key guides with small pieces of foam rubber and tweezers. This action will remove any petroleum based contaminants as well as the grease that is sometimes used on the wider keys which may have guide wires, for example, the SCACE BAR.
CLEAN KEYS
Some keys may have wires attached and some grease on them, clean these first with cotton swabs and naptha (lighter fluid). Remove all traces of the grease.
Place all keys in a kitchen strainer. Spray with household cleaner and let stand for 5 minutes. Rinse thoroughly with hot water and place keys on paper towels to dry. Let dry completely.
CLEAN RUBBER COMPONENTS
Place all rubber components in a kitchen strainer. Spray with household cleaner and let stand for 5 minutes. Use stopper in the sink so that you don´t lose these if they jump out of the strainer. Rinse these thoroughly with hot water and place on paper towels. Fold the towels over and press to squeeze most of the water out of the pieces. Let dry completely.
LUBRICATE KEYS
Place all keys bottom-up on a paper bag. Lightly coat the keys, at a 45 degree angle with Super Lube Dry Film lubricant. Do this from all 4 sides to assure penetration and coverage into the small and critical guide spaces inside each key. Let dry ( this happens nearly instantly). DO NOT overdue this step as the carrier solvent may affect the plastic.
LUBRICATE KEYBOARD
Mask off the laptop with paper and scotch tape. Apply lubricant (as above in LUBRICATE KEYS) to the keyboard and let dry.
All right, you now have perfectly cleaned and lubricated keys, keyboard, and rubber components.
REASSEMBLE
Place all rubber components into the keyboard.
Install keys with wires. Make sure wire is secured in the key, usually snapped into place. Place ends of wire in the guide slots adjacent to the key location as you align the key. Firmly press down to snap the key into place.
Install the rest of the keys by aligning and firmly pressing down.
CONTRATULATIONS, you now have a keyboard which will operate smoothly and perfectly for years to come.
Bookmarks